Electronicdesign 27496 Nanobots 892125356
Electronicdesign 27496 Nanobots 892125356
Electronicdesign 27496 Nanobots 892125356
Electronicdesign 27496 Nanobots 892125356
Electronicdesign 27496 Nanobots 892125356

Silicon Nanobot Swarms May Be Coming Sooner Than You Think

June 21, 2019
Wirelessly powered and controlled using silicon photovoltaics, a research team employed a voltage-controllable electrochemical actuator to create their “walking” nanorobots.

Swarms of nanorobots (usually referred to as nanobots) are the stuff of science-fiction movies (mostly scary, some not). However, they’re getting closer to reality as tiny, insect-like electromechanical “creatures” are being created and evaluated. But why not instead use extensions of silicon-based IC processes and leverage the many attributes and high areal density of this well-known, low-cost mass-production technique to create nanobots without discrete mechanical parts?

That’s what a team headed by Prof. Marc Miskin, assistant professor in the Department of Electrical and Systems Engineering at the University of Pennsylvania (he was at Cornell University until January 2019) has done, fabricating their nanobots directly on special silicon wafers. Taking advantage of IC-production techniques, they can create over one million functional units in a single production pass on a single 4-in. wafer (see figure).

These silicon nanorobots move as their bilayer legs are actuated by a few hundred millivolts, which are generated from a laser shining on their integral solar cells. (Source: Marc Miskin, University of Pennsylvania)

These walking nanobots are both wireless powered and controlled (to a very limited extent, at this time) using embedded silicon photovoltaics. The robots “walk” using a new type of voltage-controllable electrochemical actuator fabricated from nanometer-thick membranes on a platinum base. Their bodies are rectangular skeletons of glass about 10 µm by 70 µm and topped with a layer of silicon. The legs, about 100 atoms thick, are built as two layers, comprising platinum applied via atomic layer deposition topped with titanium (or graphene). The researchers also etched electronic-control components and either two or four silicon solar cells into the body.

The solar power isn’t used in a conventional battery/motor arrangement, of course. Instead, by shining a laser on the nanobot solar cells, the resultant voltage (about 200 mV) causes the platinum in the leg to expand while the top layer does not. This bending becomes the motor that moves their limbs. By managing the stimulation, the legs alternately expand and contract, resulting in a basic walking-like gait. This 16-second video is especially illustrative; other basic short videos are here and here.

These actuators have extremely low power requirements, on the order of nanowatts, yet can carry loads several thousand times their own weight (the strength of basic materials and their expansion/contraction strain is quite high). “The legs are super strong," says Prof. Mishkin. "Each robot carries a body that's 1,000 times thicker and weighs roughly 8,000 times more than each leg."

Taking a New Fantastic Voyage

The researchers are looking to expand the utility of these nanobots to explore their environment, and they have even “survived” being injected through a hypodermic needle. To extend their operating zone to areas where light can’t reach, such as within the human body, the researchers are exploring providing power via ultrasound energy or magnetic fields.

Prof. Miskin added that many people ask him how his nanobots compare to the submarine in the classic 1966 sci-fi movie Fantastic Voyage (it’s over 50 years old!). "It's a fundamentally different kind of robot," he said. "You can throw them away." They are so cheap to make—a fraction of a penny each—that he thinks of them like chemicals or medicines.

Future research will involve developing wireless sensors so that the robots can transmit information on vital signs from a patient, such as levels of neuronal activity in the spinal cord, says Miskin. The nanobots are small enough that they can be injected with a syringe. They also plan to study the best way to retrieve them, perhaps with magnets.

The work was presented at the March 2019 meeting of the American Physical Society Boston, in a session entitled “Fabricating Autonomous Machines for the Cellular Scale.” Funding came from a variety of sources, including the Army Research Office, the Cornell Center for Materials Research, the National Science Foundation,  the Air Force Office of Scientific Research, and the Kavli Institute at Cornell for Nanoscale Science.

Sponsored Recommendations

Understanding Thermal Challenges in EV Charging Applications

March 28, 2024
As EVs emerge as the dominant mode of transportation, factors such as battery range and quicker charging rates will play pivotal roles in the global economy.

Board-Mount DC/DC Converters in Medical Applications

March 27, 2024
AC/DC or board-mount DC/DC converters provide power for medical devices. This article explains why isolation might be needed and which safety standards apply.

Use Rugged Multiband Antennas to Solve the Mobile Connectivity Challenge

March 27, 2024
Selecting and using antennas for mobile applications requires attention to electrical, mechanical, and environmental characteristics: TE modules can help.

Out-of-the-box Cellular and Wi-Fi connectivity with AWS IoT ExpressLink

March 27, 2024
This demo shows how to enroll LTE-M and Wi-Fi evaluation boards with AWS IoT Core, set up a Connected Health Solution as well as AWS AT commands and AWS IoT ExpressLink security...

Comments

To join the conversation, and become an exclusive member of Electronic Design, create an account today!