Among Design Constraints, Power Assumes The Throne

Jan. 17, 2008
Over the past few years, the “power problem” has registered more strongly on the radars of system design teams. Portable and handheld consumer electronics keep shrinking. Hence, so do their batteries. Meanwhile, no one wants to

Over the past few years, the “power problem” has registered more strongly on the radars of system design teams. Portable and handheld consumer electronics keep shrinking. Hence, so do their batteries. Meanwhile, no one wants to sacrifice runtime in their mobile phones despite the desire to have cell phones go a long way toward replacing laptops. Thus, the onus falls on system-on-a-chip (SoC) designers to navigate the tradeoffs necessary to make that happen.

In turn, the harried designers look pleadingly to the EDA industry for methodologies that enable their quest to subvert the laws of physics. In 2008, it’s all about power for EDA, in terms of tools, methodologies, and even standards. There will be a spate of announcements having to do with low-power design in the next year or two spanning all those areas (see the figure).

Trust, but Verify
Verification remains very challenging— even more so when it’s tied to the increasing issues surrounding power consumption. It’s a given that designers must find ways to optimize and reduce energy consumption, starting at the early phases in the design process where there is more potential savings and greater implementation flexibility. But what’s sometimes overlooked is that the changes that are made to influence power can negatively impact verification.

As a result, design teams will need to invest more than ever in verification. Formal techniques are becoming more widely used to snare a growing percentage of bugs, and this trend will only accelerate. There is also broader use of electronic system- level (ESL) methodologies as designers grasp for greater productivity in both the design and verification spheres.

For 2008, look for power and ESL to increase the role of sequential equivalence checking in verification. Advanced techniques and tools such as sequential equivalence checking will complement existing simulation-based methods. Designers will spend more time on power optimization and look to automation for sequential RTL clock gating.

Decent Standards
There has been some wrangling among EDA vendors this year with respect to a uniform expression of design intent for power that can be carried throughout the flow. There are indications, though, that the battle over power formats may have a mercifully swift end in the form of a single IEEE standard.

One of the competing standards, the Unified Power Format (UPF), was created through a joint effort involving several key EDA players (Magma Design Automation, Mentor Graphics, and Synopsys) as well as a number of prominent systems houses (ARM, LSI, Infineon, Intel, Nokia, Nordic, and Texas Instruments). The UPF, which had been donated to Accellera, has now in turn been donated to the IEEE’s P1801 low-power working group.

Perhaps 2008 will be the year in which the industry coalesces around a single workable standard for the expression of power intent, which would gladden the hearts of those who depend on their flows to maintain interoperability in various respects.

What's Next
On the implementation side, we’ll begin to see a transition from timing-driven place-and-route to power-driven place-and-route. With netlists accounting for as much as 40% of the power budget, a shift to power-driven place-and-route tools can help designers identify their key sources of power consumption in a design and reduce net capacitance. Reducing routing resources can decrease dynamic power consumption by as much as 30% for a typical design, some claim.

In general, 2008 could be the real breakout year for virtual prototyping. In 2007, most large design projects attempted to use virtual prototypes in one form or another. In 2008, designers will be trying to improve the prototyping process to get more acceptable speed, accuracy, and overall usability from their prototypes. There will be efforts from EDA vendors to improve the interoperability of high-level models as well as their reusability.

About the Author

David Maliniak | MWRF Executive Editor

In his long career in the B2B electronics-industry media, David Maliniak has held editorial roles as both generalist and specialist. As Components Editor and, later, as Editor in Chief of EE Product News, David gained breadth of experience in covering the industry at large. In serving as EDA/Test and Measurement Technology Editor at Electronic Design, he developed deep insight into those complex areas of technology. Most recently, David worked in technical marketing communications at Teledyne LeCroy. David earned a B.A. in journalism at New York University.

Sponsored Recommendations

Comments

To join the conversation, and become an exclusive member of Electronic Design, create an account today!