Under the Hood of the 2007 Saturn Vue Greenline

Nov. 1, 2006
The only way to externally identify that the Saturn Vue Greenline uses an internal combustion engine and electric propulsion is by observing the hybrid logo. However, the hybrid technology of this SUV is quite different from its competitors.

Like most hybrids, the only way to externally identify that the Saturn Vue Greenline uses an internal combustion engine and electric propulsion is by observing the hybrid logo. However, the hybrid technology of this SUV is quite different from its competitors. Using a belt alternator system (BAS), the Vue's hybrid system costs less than $2,000. The mild hybrid provides fuel economy and performance benefits for drivers.

HYBRID SYSTEM

Even though the motor-generator of the BAS mounts similar to the traditional alternator, there are a few design changes that range from obvious to subtle. On the obvious side are the motor/generator, the power electronics and the battery. Subtle design changes in the Vue hybrid include the hybrid accessory drive, modified transaxle and cooling for the power electronics.

The 16-pole motor-generator provides 60 Nm of torque and 4 kW of power and generates 5 kW. The power electronics that control the motor/generator, dc-dc converter, and other functions such as the transaxle auxiliary electric oil pump, and provides 12 V vehicle accessory power weighs less than 9 kg. Concealed under the cargo floor between the rear wheels, the 36 V NiMH battery can deliver and receive more than 10 kW of peak power.

To handle peak power requirements and ensure sufficient belt tension, the hybrid accessory drive has a hydraulic strut tensioner and a friction-damped rotary tensioner on a common pivot arm. A single high-strength aramid cord belt connects the damper, A/C compressor, dual tensioner, and the motor/generator.

Modifications to the electronically controlled transaxle include the addition of an auxiliary electric oil pump that maintains oil pressure when the engine is off. A sole-noid controls the downshifting during regenerative braking. Other mechanical changes balance power and fuel economy and allow coast braking.

The vehicle's cooling system also cools the power electronics inverter and the dc-dc converter. To manage both the hybrid system and the 2.4-liter, 4-cylinder gasoline engine, the engine control module includes hybrid supervisory software that communicates via the high-speed CAN protocol.

HYBRID PERFORMANCE

With estimated fuel economy of 27 mpg city/32 mpg highway, the Vue Greenline provides a 20% fuel economy improvement over its non-hybrid counterpart. Testing conducted by independent test lab AMCI on 2006 SUVs from three other manufacturers and a standard 4-cylinder Vue show rather impressive results. All vehicles were driven over a 500-mile route that had city and highway conditions and by each of six test drivers to provide the same driving pattern. The BAS Greenline achieved 4.7 mpg over the standard Vue and was within 2 mpg of the best performing full hybrid.

The improved fuel economy strategy includes:

  • Shutting off the engine when the vehicle is stopped.
  • Restarting the engine when the brake pedal is released.
  • Shutting off fuel during vehicle deceleration.
  • Recovering vehicle kinetic energy during deceleration.
  • Charging the battery under the most efficient conditions.
  • Providing additional power from the electric motor/generator during launch and as required, such as during wide open throttle.

The motor/generator supplies additional power during launch and at wide open throttle for improved performance with a rating of 170 hp, instead of the 143 hp provided by the 2.2-liter engine in the conventional four-cylinder Vue.

Sponsored Recommendations

The Importance of PCB Design in Consumer Products

April 25, 2024
Explore the importance of PCB design and how Fusion 360 can help your team react to evolving consumer demands.

PCB Design Mastery for Assembly & Fabrication

April 25, 2024
This guide explores PCB circuit board design, focusing on both Design For Assembly (DFA) and Design For Fabrication (DFab) perspectives.

What is Design Rule Checking in PCBs?

April 25, 2024
Explore the importance of Design Rule Checking (DRC) in manufacturing and how Autodesk Fusion 360 enhances the process.

Unlocking the Power of IoT Integration for Elevated PCB Designs

April 25, 2024
What does it take to add IoT into your product? What advantages does IoT have in PCB related projects? Read to find answers to your IoT design questions.

Comments

To join the conversation, and become an exclusive member of Electronic Design, create an account today!