Electronicdesign 26216 Promo Power
Electronicdesign 26216 Promo Power
Electronicdesign 26216 Promo Power
Electronicdesign 26216 Promo Power
Electronicdesign 26216 Promo Power

Flyback-Topology DC Controller Drops Need for Optical Isolator

March 26, 2019
With the LT6813, designers can build an optoisolator-free power controller that delivers from 20- to 600-V dc output up to 100 W using an updated version of the long-established “flyback” principle.

Numerous applications can’t operate in low-voltage ranges due to the physical reality of their situation. For these installations, a converter such as the Analog Devices LT8316 600 VIN isolated flyback controller may offer a solution.

Working in conjunction with peripheral components and a flyback transformer, this IC accepts a 16- to 600-V input and delivers an isolated output of up to 100 W. It does so without a need for an optoisolator, which can bring in extra design issues such as the need for extra components (their size cost), along with performance concerns related to limited dynamic response, nonlinearity, unit-to-unit variation, and aging over its life.

The controller works by sampling (in the analog domain) the delivered output voltage as observed via a tertiary winding on the special flyback transformer. It implements a switched-mode, quasi-resonant form of boundary-mode operation to improve load regulation, reduce transformer size, and maintain high efficiency.

In a flyback design, the single magnetic component—that three-winding transformer—is used not only for voltage step-up/step-down, but also functions as a coupled inductor, thus merging three the key functions of energy storage, energy transfer, and isolation. The LT8316 supports low-cost designs such as the 94% efficient, 20- to 600-V input, 54-V output isolated supply shown in the figure. The datasheet provides other designs, as well.

This flyback-topology power converter based on the LT8316 provides an isolated 54-V dc output from an input between 20 V and 600 V, with 94% efficiency. (Source: Analog Devices)

Updating a Classic

If the flyback-converter concept sounds new, it’s not. It was developed the 1930s and matured in the 1940s and 1950s when it was used in nearly every TV to develop the high voltage (~20 kV) needed by the CRT display. The flyback approach features low parts count and inherent input/output isolation, critical in those mass-market applications, Modern versions often use an optoisolator, but the LT8316 is a much-updated semiconductor version of the classic design. It, too, uses that third winding on the transformer for the feedback signal. (The References below provide additional insight into flyback topology, operation, and construction.)

The LT8316 controller goes beyond those classic CRT-based flyback designs, with constant-current and constant-voltage regulation; in normal operation, the current source turns off and the device gets its power from that third transformer winding to minimize standby-power dissipation. Quiescent current is just 75 μA, while the device also provides low-ripple operation during light-load periods. Other features include programmable current limit and soft-start to minimize transients and component stress.

The flyback transformer isn’t just a simple turns-ratio magnetic component, so the datasheet explains in detail how to determine its specifics and size it for the voltage, current, and power requirements. (In most projects, of course, specific transformer selection has subtleties and is rarely as simple as their underlying basic turns-ratio principle and power rating implies.)

Since the transformer specification and design is likely the most critical part for successfully implementing any flyback design, Analog Devices worked with several leading magnetic-component manufacturers to produce pre-designed flyback transformers for use with the LT8316. These are called out on the datasheet for different voltage combinations along with the vendors and their model numbers.

The LT8316 is housed in a modified, thermally enhanced 20-pin TSSOP package, but with four pins removed to meet high-voltage spacing mandates. Pricing starts at $2.18 each (1000-piece lots).

References

Texas Instruments, “Understanding the Basics of a Flyback Converter

Electrical Engineering Stack Exchange, “How does a CRT television flyback really operate

Autodesk Instructables, “2n3055 Flyback Transformer Driver for Beginners

Robert Gawron, “High voltage supply (10-30kV) made from CRT television flyback transformer

Electronc Repair Guide, ”What Is Flyback Transformer?”

Wikipedia, “Flyback transformer

Sponsored Recommendations

Highly Integrated 20A Digital Power Module for High Current Applications

March 20, 2024
Renesas latest power module delivers the highest efficiency (up to 94% peak) and fast time-to-market solution in an extremely small footprint. The RRM12120 is ideal for space...

Empowering Innovation: Your Power Partner for Tomorrow's Challenges

March 20, 2024
Discover how innovation, quality, and reliability are embedded into every aspect of Renesas' power products.

Article: Meeting the challenges of power conversion in e-bikes

March 18, 2024
Managing electrical noise in a compact and lightweight vehicle is a perpetual obstacle

Power modules provide high-efficiency conversion between 400V and 800V systems for electric vehicles

March 18, 2024
Porsche, Hyundai and GMC all are converting 400 – 800V today in very different ways. Learn more about how power modules stack up to these discrete designs.

Comments

To join the conversation, and become an exclusive member of Electronic Design, create an account today!