Temp Sensor think large
Temp Sensor think large
Temp Sensor think large
Temp Sensor think large
Temp Sensor think large

“Linear” PTC Thermistors Overcome NTC Temperature-Sensing Shortcomings

May 15, 2020
A family of PTC thermistors conquers the calibration and linearity errors associated with conventional NTC temperature devices.

Temperature is the most widely measured physical variable and designers have many sensing options, among them thermocouples, RTDs, solid-state current-output sensors, and thermistors, to cite just a few. Among these, negative-temperature-coefficient (NTC) thermistors are widely used for temperature sensing in industrial, automotive, medical, instrumentation, and consumer applications due to their low cost, wide range, and relative ease of interfacing.

However, NTC thermistors do have well-known drawbacks. Along with their large temperature coefficient of resistance (good), they have a highly nonlinear (albeit smooth) curve of resistance versus temperature (not good). As a result, circuit and system designers must implement one or more strategies to deploy them effectively. Such techniques include multipoint calibration, employing multiple thermistors with overlapping ranges, lookup tables (often aided by interpolation), or performing correction calculations based on the standard Steinhart-Hart equation (or a simplified regression  polynomial), which models their transfer function.

Recognizing both their attractiveness and shortcomings, Texas Instruments (TI) has introduced a family of silicon-based positive-temperature-coefficient (PTC) thermistors—the complement of NTC devices—with what they maintain is 50% higher accuracy. For example, the TMP61 is a highly linear PTC thermistor with 10-kΩ nominal resistance at 25°C, with ±1% maximum nonlinearity from 0 to 70°C and a –40 to +125°C operating range (Fig. 1).

It offers consistent sensitivity across the temperature range with a temperature coefficient of resistance (TCR) of 6400 ppm/°C at 25°C and 0.2% typical TCR tolerance across the operating range (the similar TMP63 has 100-kΩ nominal resistance at 25°C, as does the 47-kΩ TMP64). Compared to NTC devices, the thermistors require little or no linearization circuitry or software, require only single-point calibration, have less resistance-tolerance variation, and offer higher sensitivity at high temperatures.

TI claims that by eliminating the need for additional linearization circuitry or redundant NTC thermistors, these PTC thermistors simplify design, lower system cost. and reduce printed-circuit-board (PCB) layout size by at least 33% when compared to NTC thermistors.

As with all devices, and especially temperature sensors that are often in hostile environments, failure is indeed an option and possibility. Thermistors can be driven by a voltage or current source (Fig. 2), and while there are pros and cons to each drive approach, a short circuit could have system-wide implications. For this reason, the TI devices include a built-in “fail-safe” in the event of short-circuit failures.

Of course, physical sensor size is a factor in temperature sensing, as sensor thermal mass affects both response time and ability to site the sensor close to the point of interest. Among the available packages, the TMP61 is offered in 0.60- × 1.00-mm (0402 footprint compatible), 4.00- × 3.15-mm (TO-92S), and 0.80- × 1.20-mm (SOT-5X3) packages; the TMP63 comes in a 0.60- × 1.00-mm package, and other TMP packages are available. In addition, the 10-kΩ TMP61 and 100-kΩ TPM63 are available in automotive-grade versions. Prices begin at US$0.05 in 1,000-unit quantities.

For test and evaluation, TI offers the TMP6EVM evaluation kit, which is powered via a USB connection or a CR2032 coin-cell battery (Fig. 3). This standalone module includes the company’s TMP116 digital sensor for local temperature reference along with two analog channels. The sensor section of the circuit board can be separated from the main board to emulate a system where the sensor is remotely located from the host controller (a common situation), while the LCD displays real-time streaming of temperature measurements at a 2-Hz update rate.

Full product details, including links to individual datasheets, access to a thermistor-design tool, and a short video, are available here, while details on the TMP6EVM are posted here. There’s also a useful, highly readable tutorial and application white paper “Temperature sensing with thermistors.

Sponsored Recommendations

Board-Mount DC/DC Converters in Medical Applications

March 27, 2024
AC/DC or board-mount DC/DC converters provide power for medical devices. This article explains why isolation might be needed and which safety standards apply.

Use Rugged Multiband Antennas to Solve the Mobile Connectivity Challenge

March 27, 2024
Selecting and using antennas for mobile applications requires attention to electrical, mechanical, and environmental characteristics: TE modules can help.

Out-of-the-box Cellular and Wi-Fi connectivity with AWS IoT ExpressLink

March 27, 2024
This demo shows how to enroll LTE-M and Wi-Fi evaluation boards with AWS IoT Core, set up a Connected Health Solution as well as AWS AT commands and AWS IoT ExpressLink security...

How to Quickly Leverage Bluetooth AoA and AoD for Indoor Logistics Tracking

March 27, 2024
Real-time asset tracking is an important aspect of Industry 4.0. Various technologies are available for deploying Real-Time Location.

Comments

To join the conversation, and become an exclusive member of Electronic Design, create an account today!