Evolution1088 | Dreamstime.com
Airplane Led Lighting Promo

Building a Versatile LED Driver

March 30, 2021
Configurable LED drivers, whether implementing a buck, boost, or buck-boost topology, provide a versatile approach to LED design, delivering efficient operation over a wide input voltage range while providing up to 1-A LED string current.

This article is part of the Power Management Series: Driving LED Designs

What you'll learn:

  • Different topologies used in developing LED drivers.
  • Proper connections for buck, boost, and buck-boost configurations.
  • Test results for the three topologies using the same LED string.

Today’s LED drivers are highly flexible, enabling their use in a wide array of applications from scanners to automobiles to avionic lighting. Many of these drivers can also be configured using multiple topologies —boost, buck, and buck-boost—to meet a wide variety of specific application requirements.

For low input voltages and high string voltages, a boost topology is appropriate, whereas a buck is more suitable for high input voltages and low string voltages. A buck-boost topology is used for a wide range of inputs where voltage can be below or above the LED string.

This article covers the process of selecting the suitable topology and its corresponding connections. For purposes of illustration, the examples are based on the LTM8042 µModule LED driver. This driver supports LEDs with up to 1-A current and a 3000:1 dimming ratio, operates from input voltages of 3 to 30 V, and has a frequency range of 250 kHz to 2 MHz.

Boost LED Driver

The most common topology for an LED driver is a boost application, as might be used for an LED array powered from a 12-V input rail, where VIN < VF. A boost approach is shown in Figure 1, with a block diagram shown in Figure 2.

1. Here, the LTM8042 is driving four LEDs; VIN 5.75 to 10.25 V and IOUT = 0.5 A.

2. The LTM8042 block diagram shows connections in a boost configuration.

The input voltage is connected to the BSTIN/BKLED– terminal and the LED string cathode is connected to GND. When transistor Q is on, the current builds up in the inductor L. Once Q turns off, the voltage across L changes polarity and the inductor current begins flowing to output filter capacitor C2. LED dimming is implemented in the PWM section, which regulates the duty cycle, and by extension, the average LED current (set by resistor RCLR). Capacitor C1 is an input voltage filter.

Buck LED Driver

A buck topology is used for relatively high input voltages, such as automotive and industrial 24-V rails. Figure 3 shows a block diagram for a configuration for VIN > VF. The input voltage is connected to the BSTOUT/BKIN terminal and the LED cathode is connected to the BSTIN/BKLED– terminal.

3. This LTM8042 block diagram shows connections in a buck configuration.

When transistor Q is on, current flows from the input through the LED string and inductor L to GND. Once Q turns off, the voltage across L changes polarity and diode D becomes forward-biased. This pulls the LED cathode below the input voltage level, providing the set value of the current in the LED string. C5 creates an output filter for this topology.

Buck-Boost LED Driver

In many commercial, battery, and solar-powered applications, the input voltage varies over a wide range. In these situations, the buck-boost topology shown in Figure 4 is the best solution. The input voltage and LED cathode are connected to the BSTIN/BKLED– terminal.

4. The LTM8042’s connections are depicted in a buck-boost configuration.

When transistor Q is on, the current builds in inductor L. Once Q turns off, the voltage across L changes polarity, forward-biasing diode D while the voltage climbs above the input level. The pulse-width modulator (PWM) maintains the set value of current through the LED and C5, and C2 functions as an output filter. The LED string voltage VF can be below or above VIN.

Test Results for the Three Topologies

All three topologies were tested using the DC1511 demonstration circuit featuring the LTM8042—utilizing the same LED string, output current, and switching frequency in all cases. To make sure that bias power dissipation is the same for all three settings, the same VCC (shown in Figure 1) was supplied as well. The VCC pin can be tied to VIN in most cases.

Figure 5 shows the resulting efficiency curves. All three topologies also were modeled in LTspice environments; simulation files related to LTM8042 can be found in its datasheet.

5. The plot shows LTM8042 efficiency for boost, buck, and buck-boost configurations.

The result is that configurable LED drivers provide a versatile approach to LED design, delivering efficient operation over a wide input voltage range while providing up to 1-A LED string current. Because these drivers can be readily applied as a boost, buck, or buck-boost driver, the same driver can be used to meet the requirements of a diverse variety of applications.

Read more from the Power Management Series: Driving LED Designs

Sponsored Recommendations

What are the Important Considerations when Assessing Cobot Safety?

April 16, 2024
A review of the requirements of ISO/TS 15066 and how they fit in with ISO 10218-1 and 10218-2 a consideration the complexities of collaboration.

Wire & Cable Cutting Digi-Spool® Service

April 16, 2024
Explore DigiKey’s Digi-Spool® professional cutting service for efficient and precise wire and cable management. Custom-cut to your exact specifications for a variety of cable ...

DigiKey Factory Tomorrow Season 3: Sustainable Manufacturing

April 16, 2024
Industry 4.0 is helping manufacturers develop and integrate technologies such as AI, edge computing and connectivity for the factories of tomorrow. Learn more at DigiKey today...

Connectivity – The Backbone of Sustainable Automation

April 16, 2024
Advanced interfaces for signals, data, and electrical power are essential. They help save resources and costs when networking production equipment.