Upon entering its fourth decade, you’d think Ethernet would show signs of age, being pushed aside for newer, stateof- the-art networking technologies. Well, ummm, no.
Rather, Ethernet has evolved in step with changing requirements and standards. In the beginning, it involved PC ports on a coax bus local-area network (LAN). Over time, the technology has morphed into many other forms of networking, from simple I/O ports on embedded controllers to metroarea- network (MAN) and wide-area-network (WAN) implementations including backbone and backhaul—not to mention wireless (see “Ethernet: A History”).THE 10-GBIT/S ROLLOUT The 10-Gbit/s version of Ethernet has been around for more than five years in several forms. But it has taken time for prices to moderate and companies to adopt these higher-speed versions. Usually, 10/100 Ethernet works for most small and medium businesses, and 1 Gbit/s is fast enough for an aggregation backbone.
Yet with ever-larger networks, more wireless extensions, and larger data flows, the advent of 1 Gbit/s to the desktop and 10-Gbit/s backbones has become necessary. With server virtualization, the increased growth of data centers and server farms with blade servers, the growing number of Internet searches, video downloads, and streaming video, the need for 10-Gbit/s networks is critical.
Today, 10-Gbit/s equipment is more common and becoming the main link between servers in data centers. While most 10-Gbit/s LANs are fiber, the newer copper unshielded twisted-pair (UTP) version is slowly being adopted in data centers and other short-distance (<30 to 100 m) applications.
The 10-Gbit/s copper version (10GBaseT) is an interesting technical case because it virtually defies the laws of physics. To achieve that seemingly impossible rate, the standard calls for 16 levels of pulse-amplitude modulation (PAM) simultaneously occurring at an 800-Msymbol rate over each of the four pairs in a special low-loss CAT6a UTP. A low-density parity check (LDPC) coding scheme helps overcome data errors due to cable losses and noise.
On top of that, all sorts of fancy equalization, echo, and crosstalk cancellation for near-end crosstalk (NEXT), far-end crosstalk (FEXT), and alien (adjacent cables) crosstalk are implemented with DSP. Lots of circuitry (i.e., 800-MHz 10-bit analog- to-digital converters, DSP logic) is used to achieve these connections, making most implementations power hogs. Several companies have brought the power consumption per port down to 3 to 5 W, which is barely acceptable.
Yet 10GBaseT is still significantly lower cost per port than fiber versions. While 10-Gbit/s copper network interface cards (NICs) are now available, 10GBaseT has never really taken off, primarily because of the rivalry and squabbling between the competing companies over intellectual property (IP) and other issues. This small group of companies has never come together to build a market despite the fact it did actually agree on a standard (802.3an).
A variety of Ethernet optical modules is now available in X2, XFP, SFP, and other multisource agreement (MSA) formats. With the new SFP+ optical transceiver modules for 10 Gbits/s now priced competitively, there may be fewer reasons to keep the copper version. The market will no doubt let us know.THE 40/100-GBIT STANDARD With Ethernet steadily increasing in speed, there have been debates on its use as a network backbone and in core MANs and WANs. It’s highly desirable due to its fully standardized nature, which includes full interoperability and backward-compatibility between the components of many different vendors. Its low cost is also attractive, as is the fact that it’s well-known among IT and network personnel. The forthcoming 40- and 100-Gbit/s versions will make Ethernet a real contender in the MAN and WAN space.
Right now, Sonet/SDH is still the leading technology in these core, edge, and access networks. Sonet/SDH networks of the OC-48 (2.5 Gbits/s) and OC-192 (10 Gbits/s) varieties see wide usage. Also, Sonet/SDH defines standards to OC-768 or 40 Gbits/s. The 40-Gbit/s versions aren’t common, but are now getting more play. Holding back their widespread adoption is the high price.
Thanks to developments in 10-Gbit/s Ethernet, semiconductors, and optical processing, data rates are reaching 100 Gbits/s. In 2006, the IEEE established the High Speed Study Group (HSSG) to investigate the development of a 100-Gbit/s standard. Then in 2007, the group agreed to add a 40-Gbit/s version as an interim technology for data centers and other markets.
Continue on Page 2
An organization called the Road to 100G Alliance was formed in 2008 to study the problem and make recommendations. That Alliance was rolled into the Ethernet Alliance in late 2008. In early 2008, the IEEE established a Task Force to create the new 40/100-Gbit/s standard designated 802.3ba. A final standard isn’t expected until 2010.
Additionally, the International Telecommunications Union-Telecommunications (ITU-T) has a 100-Gbit/s standard study group that’s looking into this technology (designated as Recommendation G.709). Overall, several versions are possible, and most of them involve parallel data paths on fiber-optic cable.
The 40-Gbit/s standard would simply put four 10-Gbit/s data streams on four parallel fibers. One 100-Gbit/s version would require eight or ten 10-Gbit/s data paths on parallel fibers. These two versions would be used primarily in short runs, for example, in data centers. For longer runs, coarse or dense wavelength-division multiplexing (DWM) using four or eight/ten wavelengths (?) of light on a single fiber is an option.
Whatever the technique, the industry’s ultimate goal is a 100-Gbit/s rate for up to 40 km (25 miles) and up to 10 km (6 miles) on single-mode fiber (SMF), as well as up to 100 m (328 ft) on optical multimode 3 (OM3) multimode fiber (MMF). Possibilities include the use of SNAP-4 or quad small form-factor pluggable (QSFP) cables and connectors for 40 Gbits/s, as well as SMAP-12 cables and connectors for 100 Gbits/s.
The Optical Internetworking Forum (OIF) is working with the IEEE group on a version that would transmit 25 to 28 Gbits/s over four parallel paths. A single serial version over SMF isn’t expected because of the attenuation and dispersion problems at such high data rates. A copper version with a reach of 5 to 10 m or a backplane version may be included in the standard.
A variety of modulation schemes such as differential phase-shift keying (DPSK) and differential quadrature phase-shift keying (DQPSK), dispersion compensation, and forward-error-correction (FEC) coding methods is being considered. Further goals include the support of full duplex operation and maintaining the frame format and media-access-controller (MAC) interface, as well as having a bit error rate (BER) of better than 10–12 at the MAC interface.
Designers can use the Sierra Monolithic SMI4027 multiplexer/clock multiplier unit (MUX/CMU) to implement 40-Gbit/s systems (Fig. 1). It and its companion SMI4037 clock and data recovery unit/ demultiplexer (CDR/DEMUX) implement the physical layer (PHY), operate from 39.8 to 44.6 Gbits/s, and incorporate a fully SFI-5 client-side interface. Furthermore, they are fully usable with Sonet/SDH or with Ethernet.CARRIER ETHERNET Ethernet has always been a “best effort” networking service, meaning not all packets may be received. Packets could be dropped because of noise, collisions, packet payload violations (too long, too short), or other reasons. Its non-deterministic characteristics caused by latencies and variable delays also diminish its usefulness in some applications.
These flaws make Ethernet questionable for serious data services such as financial and healthcare transactions, video streaming, and other mission-critical applications where quality of service (QoS) is mandatory. Sonet/SDH is a guaranteed service, and that’s the reason for its continued use and development despite costs and complexity. Now an alternative known as Carrier Ethernet is turning Ethernet into a service with similar qualities.
Created by the Metro Ethernet Forum (MEF) and its members, Carrier Ethernet defines a set of standards and implementation agreements for a carrier-class service and network that distinguishes it from LAN Ethernet. Also, it defines five basic attributes that make Ethernet function at the carrier-grade level in the access, metro, and core networks:
• Standard services such as E-Line, E-LAN, and transparent private line, virtual private line, and LAN service; it’s suitable for converged voice, video, and data networks with choice and granularity of bandwidth and QoS options
• Scalability across access, metro, and wider area networks
• Reliability, implying the ability to detect and recover from incidents without impacting users
• QoS with service level agreements (SLAs)
• Service management, meaning the ability to monitor, diagnose, and centrally manage the network; carrier-class operation, administration, and management (OAM); and rapid provisioning
The MEF provides testing procedures and certification to ensure that the standards are met and interoperability is achieved. Carrier Ethernet is implemented by equipment like RAD Data Communications’ demarcation device (Fig. 2).
Continue on Page 3STORAGE-AREA NETWORKS Storing large quantities of data is common in the enterprise, government, and other organizations. RAID (redundant array of independent disks) and JBOD (just a bunch of disks) storage systems are a growing market, and the need to connect them to LANs and the Internet is critical. That’s why special storage-area networks (SANs) were developed.
The most widely used SAN, Fibre Channel (FC), is an optical-fiber network that connects the hard-disk arrays to the servers and the network through host bus adapter (HBA) cards. The medium is fiberoptical cable, and the T11 organization has set standards for data rates of 1, 2, 4, and 8 Gbits/s. Also, a 10-Gbit/s standard has been defined.
Though FC works well and is widely used, it’s expensive to expand and maintain. Nonetheless, most users want to continue it in some way even though lower-cost alternatives like the Internet Small Computer Systems Interface (iSCSI) are out there.
The iSCSI option is a serial version of the widely used older SCSI parallel connections and protocol used with hard drives. It uses Ethernet as the networking medium to tunnel SCSI commands and data. As a result, it costs much less and can run in parallel with existing Ethernet networks. But, except for small and medium businesses, iSCSI’s adoption has been limited.
A forthcoming alternative that combines the best of FC and Ethernet is the Fibre Channel over Ethernet (FCoE) standard being developed by the T11 organization. It packages FC packets and tunnels them over standard Ethernet LANs.BUT THAT'S NOT ALL... Many other enhancements, additions, and applications surround Ethernet, such as industrial Ethernet, the LXI instrumentation system, and Ethernet passive optical networks (EPONs).
Industrial Ethernet uses standard Ethernet in place of other special networks developed for the harsh and critical nature of industrial applications. These networks have to operate with high levels of noise and in extreme environments of temperature variations and corrosive atmospheres. Special shielded and protected cables and connectors help in these cases.
In addition, many industrial applications require determinism. That is, they must be able to accurately time data transmissions and related control and measurement actions.
Ethernet is fraught with latencies, delays, and timing inaccuracies common to a best effort service. One solution is to apply the IEEE’s 1588 Precision Time Protocol (PTP). It provides accurate synchronization of nodes on a network by using hardware-generated time stamps. Precision in the nanosecond range is possible. Employing 1588 PTP on Ethernet suits this combination for even the most time-critical industrial applications. The IEEE 1588 PTP is also used in Carrier Ethernet applications.
LXI (LAN eXtensions for Instrumentation) is the relatively new instrumentation communications standard designed to replace the general-purpose instrumentation bus (GPIB) so widely used in test systems over the years. It connects test instruments, PCs, and the Internet for any combination of testing, measuring, recording, storing, and accessing data. Many instruments already incorporate LXI, and more are forthcoming. LXI is based on the use of Ethernet because of its low cost and wide availability.
Finally, work is underway on a 10-Gbit/s version of Ethernet designed for PONs in metro networks that deliver digital TV and Internet access services. PONs use low-cost fiber to distribute video and other services to homes and businesses without the need for costly repeaters or other active intermediary hardware in the field. PONs are widely deployed in cable TV and telecom infrastructures to deliver higher speeds and quality video.
The original PON standards, which were set by the ITU-T, are designated as APON, BPON, and the latest, GPON. There’s also a low-speed Ethernet PON known as EPON or GEPON for gigabit service. Designated 802.3ah, it is widely used in Asia but not in the U.S., where GPON is the dominant standard. The IEEE is currently working on a 10-Gbit/s version designated 802.3av that will utilize different wavelengths of light for 1- and 10-Gbit/s services on a single fiber. A final version of 802.3av is expected later in 2009.