Dostal's Designs: Ideas for Design Series

March 14, 2023
Analog Devices' Frederik Dostal presents this Ideas for Design video series about power and analog tips.

This video series is part of Electronic Design's Ideas for Design series.

This is the starting point for my Ideas for Design (IFD) series that includes design tips and tricks that you might find interesting. Each one includes diagrams and descriptions of small projects that highlight an approach or methodology along with a short video talking about these. You can also check out my other articles on Electronic Design

Here is the list of the latest and upcoming video articles that you might find interesting. Add a comment below if you have any questions or suggestions. 

- Frederik Dostal

Latest Dostal's Designs

Buck-Boost Voltage Conversion, the Quiet Way
Combining a buck-boost topology and Silent Switcher technology brings very low EMI at the highest power-conversion efficiency.

Dostal's Design Series

Considerations When Designing GAN-Based Switch-Mode Power Supplies
GaN switches promise higher efficiency and higher power density in SMPS. This article discusses the readiness of this technology and its challenges, and provides an outlook on...
Why You Need Level Shifting in Buck-Boost Circuits
Inverting buck-boost circuits are commonly used to generate negative supply voltages from positive voltages. However, additional level-shifting circuits may be necessary if the...
Dreamstime_wavebreakmedialtd_108378539
New innovation in the nanopower space allows for single or multiple alkaline battery cells or Li-ion batteries to power devices such as sensors and meters.
When Overvoltages Last a Long Time, Use Switching Surge Stoppers
Rather than use linear surge stoppers for overvoltage protection, opt for switching surge varieties, as the load will continue running even when surges last for a long time.
Maxresdefault 64c295b610f4d
How exactly is the correct inductance value chosen? Frederik Dostal looks at the considerations and what happens when selecting a current ripple that’s too high or too low.
Ed Dostal Promo
Excessive current flow must be prevented so that the electrical circuit can be reliably protected.
Voltage Converters Can Help Improve Battery Power Efficiency
This article explains how to extend the battery lifetime of a device by adding a nanopower converter to an existing system, which may increase the battery run time by up to 20...

More Dostal Articles and Ebooks

Power Supply Part 0
This article series aims to provide a simplified understanding and renewed appreciation for the art of power-supply design.
Promo 1
Miniaturizing a supply not only saves on space, but it lowers cost due to smaller board space requirements as well as offering the possibility of building higher-functionality...
Dreamstime_Verticalarray_29944431
Dreamstime Verticalarray 29944431 Promo
When it comes to the control aspect in switching regulators, current mode is often the preferred choice over voltage mode. This article looks at the multiple advantages—and some...
Dreamstime_Montree-Nanta_243171613
Dreamstime Montree Nanta 243171613 (1)
When designing and evaluating boost converters, sometimes the intended output voltage isn’t realized. Instead, it has a lower value than desired.
Ifd Base Promo
The speed and regulation stability of the control loop for a power supply’s fixed output voltage can be observed and assessed with a Bode plot. Here’s how it’s done.
Monolithic Prom Onew
Build a switching regulator monolithically or with a controller? Both options offer benefits, but the monolithic route often saves time and space, and exhibits better EMC behavior...
Schweiber Prom Onew
By adding a resistive divider and dc voltage to a standard dc-dc regulator, you can easily develop dc rails below 1 V, all the way down to just a few hundred millivolts.
About the Author

Frederik Dostal | Power-Management Technical Expert

Frederik Dostal is a power-management expert with more than 20 years of experience in this industry. After his studies of microelectronics at the University of Erlangen, Germany, he joined National Semiconductor in 2001, where he worked as a field applications engineer, gaining a lot of experience in implementing power-management solutions in customer projects. During his time at National, he also spent four years in Phoenix, Arizona (USA), working on switch-mode power supplies as an applications engineer.

In 2009, he joined Analog Devices, where since then he held a variety of positions working for the product line and European technical support, and currently brings in his broad design and application knowledge as a power-management expert. Frederik works in the ADI office in Munich, Germany.

Also check out my:

Sponsored Recommendations

Comments

To join the conversation, and become an exclusive member of Electronic Design, create an account today!